Department of Design and Production of Radio Electronic Equipment

National Technical University of Ukraine
"Igor Sikorsky Kyiv Polytechnic Institute"

Smart control device of electricity consumption

Author: Kovbych Anton

Group: РІ-21

Supervisor: Liashok Alina

ELK: Bachelor

Speciality: 6.050902 Radioelectronic Devices

Summary: Diploma project entitled “Smart control device of electricity consumption” written on the 90 pages, including 29 illustrations, 4 tables, 4 appendix and 33 citations. The aim of this project is to find the way to determine the value of a variable amperage and voltage with minimal size and reading this value by microcontroller for further processing, such as for transmission over the air for processing, storage and output in a user friendly manner. To address this goal was examined existing methods for determining the required quantities, advantages and disadvantages of each of them, usability and other factors which very significantly influence the final choice of the way.

Keywords: microcontroller, avr, arduino, atmega328, amperage sensor, voltage sensor, hall effect, capacitor power supply

The work consists of  71 pages of explanatory note, 4 appendix and 6 drawings

Explanatory note: Full text

Drawings:

Digital processing of the output signal of high sensitivity radiometric system for biomedical research

Author: Dolich Denys

Group: РВ-22

Supervisor: d.t.s., prof., Yanenko Alexey

ELK: Bachelor

Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

Summary: The degree project consists of an explanatory note on 71 pages, contains 17 illustrations, 22 tables, 10 drawings, 21 link, 2 appendices. The aim of the project is development of a device for digital-processing the original analog signal from high sensitive radiometric system (RS), and output processing information on the PC screen that extends the functionality and improves the metrological characteristics of the RS. Were made assessment of the existing technical solutions for such equipment and decided to construct device without unnecessary for us functionality. To do this, we developed a block diagram, and electrical circuit. For the developed scheme we selected optimal component database. Based on these data, we developed the PCB in the Altium Designer Summer 09. Also developed a case for our device. The result is a much cheaper and more accurate device than considered analogues at the expense of cutting functionality. The developed device can be used in conjunction with any system where you need to measure the constant component of the signal within 0 – 5V.

Keywords: radiometry, micro-controller, integrator, approximation, digital processing

The work consists of  70 pages of explanatory note, 2 appendix and 10 drawings

Explanatory note: Full text

Drawings:

The monitoring system measurement signal sensors

Author: Spilchuk O.V.

Group: РІ-21

Supervisor: Novosad A.A.

ELK: Bachelor

Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

Summary: Diploma project consists of 80 pages containing 37 illustration with 15 tables, 4 applications and 20 references. The aim is to develop a centralized monitoring system, which is designed to monitor, store and analyze measurement results of all devices registered in the system. The system consists of a device to read data from sensors and software (web interface), which enables analysis and visualization of measurement for each registered device in the system. The calculations confirm efficiency of the device and compliance with all regulations and standards.

Keywords: monitoring system, measurement accounting

The work consists of  80 pages of explanatory note, 4 appendix and 7 drawings

Explanatory note: Full text

Drawings:

  • Схема електрична принципова
  • Друкована плата
  • Складальний кресленик
  • Структурна схема
  • Веб-інтерфейс
  • Веб-інтерфейс. Архітектурні рішення
  • Структура бази даних
  • Landing page for applicant

    Author: Nychyporuk Vitalii

    Group: РБ-21

    Supervisor: Phd, docent, Demianenko Petro

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: Structure and scope of work. Guidance note of degree project consists of five chapters, contains 27 pictures, 5 tables, 1 website, 11 sources. During the execution of the thesis was investigated landing page leading universities and faculties in the world. The main sections of content and technology to implement. Described and depicted the implementation of certain functions using screenshots and demonstration code. Different methods for implementing specific functions. Based on the data obtained in the analysis were formed design and basic functionality of the page. Processed means of determining the effectiveness of the site and investigated what information is needed for the majority of applicants for admission to the university. It highlights the main sections which provided easy access via the navigation menu. In the annex to this main groups found in social networks and provide fast access via the left menu. The current most accurate user behavior on the Internet, namely students. To design a page used the following tools: PHP language and Java Script, and markup language HTML and CSS styles. Frameworks Modernizr jQuery. The description of development tools and a list of the main advantages of the selected products. It examined the premises and working conditions during software development. Considered harmful and dangerous factors that can affect humans. The analysis of lighting, noise, radiation. Done calculation of artificial lighting for the room. Describes safety.

    Keywords: landing page

    The work consists of  63 pages of explanatory note, 1 appendix and 3 drawings

    Explanatory note: Full text

    Posters:

  • Структура сайту
  • Статистика браузерів
  • Головні секції сайту
  • The analysis of the software and hardware input/output tools for LABVIEW

    Author: Voronchak Anatolii

    Group: РІ-21

    Supervisor: Сandidate of Engineering Sciences, senior lecturer, Turovskyi Anatolii

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: Thesis consists of 79 pages and contains 35 figures, 2 tables, 31 reference. The aim of the project is to analyze the possibilities of data input/output from LabVIEW and practical application of the analysis in the developing of universal layout for laboratory studies of radiators of electronic components. The work consists of five sections. The modern modules for LabVIEW, which can help you to implement the functions of input/output, were analyzed. The capabilities of modern hardware, which can be operated using LabVIEW, were analyzed. LabVIEW module and hardware tools, by which developed the laboratory model, were selected. The calculations of circuit elements were executed. A program to study the effectiveness of radiators were established. The problems of occupational health and safety in the process of development of the model were considered.

    Keywords: labview, hardware tool, laboratory layout

    The work consists of:  79 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    The device for measuring the light ripple

    Author: Shunkov Vitalii

    Group: РВ-21

    Supervisor: Tarabarov Sergii

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: Explanatory note of size of 70 pages contains 13 illustrations, 14 tables, 3 bibliographical applications and 11 names on the list of bibliography. The aim of the diploma project is to develop a device for measuring the ripples of light. Reviewed the comparative analysis of existing solutions, modeling of individual components of the project in program “NI Multisim”, design in CAD “Altium Designer” and the development of individual parts of the microcontroller program in the programming language “C”. The result of this work is design documentation. The developed device can be used to assess the quality of artificial light sources, namely, the ripple factor.

    Keywords: ripple factor, lighting, pcb, microcontroller, program

    The work consists of  70 pages of explanatory note, 3 appendix and 5 drawings

    Explanatory note: Full text

    Drawings:

  • Схема електрична принципова
  • Креслення друкованої плати
  • Складальне креслення
  • Структурна схема
  • Креслення корпусу
  • Module of communication virtual instruments with external device

    Author: Shelenhivskyi Oleksandr

    Group: РІ-21

    Supervisor: Turovskyi Anatolii

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: In this diploma a control module, which include system of commands of exchanging data and control of peripheral devices with the environment of virtual devices LabVIEW has developed. The work consists of five sections. Analysis of peripheral devices and their capabilities and performance of existing solutions has made. A commands set is developed and convenient use of LabVIEW environment is provided. Also the problems of health and safety while using the computer was reviewed. A diploma includes 64 pages, 29 pictures, 11 tables, 1 annex and 16 used sourses.

    Keywords: microcontroller, avr, arduino, atmega328, labview, national instruments.

    The work consists of:  64 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Device monitoring parameters motorcycle

    Author: Gannoshyn Eduard

    Group: РІ-21

    Supervisor: Turovskii Anatolii

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: In the graduation thesis a motocomputer is designed. The device can be in-stalled on any motor vehicle. Before the installation some settings are necessary. The thesis includes analysis of well-known constructions. Considering all the advantages and disadvantages of the reviewed constructions the device for motorcycles parameters monitoring has been designed. The following tasks have been accomplished: development of the structural scheme, development of the schematic, selection of components, component selection, development of printed circuit board, analysis of the overall design. The device is recommended for installation on any motor vehicle after all the initial parameters listed in the specifications of the machinery where the device will be installed. The graduation thesis consists of explanatory note covered on 98 pages. It includes 46 figures, 7 tables, 4 drawings, 23 references, 2 appendices.

    Keywords: motocomputer, microcontroller, printed circuit board, electronic control unit

    The work consists of  97 pages of explanatory note, 3 appendix and 4 drawings

    Explanatory note: Full text

    Drawings:

  • Блок схема
  • Схема електрична принципова
  • Друкована плата
  • Друкований вузол
  • Research dispersion compensators using optical fibers with negative dispersion

    Author: Diachenko Radomyr

    Group: РІ-21

    Supervisor: Demyanenko Peter

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: Explanatory note takes 73 pages of typewritten text. It used 8 tables and figures 13 formula 38 show letters 11 sources of scientific technical literature, 3 applications. The aim is — the study of methods to search for optical fibers with negative dispersion used as dispersion compensators. The purpose of development — selecting optical fibers with negative dispersion compensators for use in dispersion compensators calculation of the main features using selected fibers. Scope — modernization of lines built on standard single mode fiber (recommendation G.652), the design lines.

    Keywords: dispersion, optic fiber, dispersion compensation, dispersion compensators, fibers with negative dispersion fiber bragg grating.

    The work consists of:  74 pages of explanatory note and 3 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    The interface of the system “Smart House”

    Author: Chebotar Dmytro

    Group: РВ-21

    Supervisor: Adamenko Vladimir

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: Thesis is devoted to developing software with an intuitive management interface of the whole house, namely: light, temperature, heating, automatic control of Windows and blinds. Also file the idea of creating a web server for further system development. The theme of this work is relevant in relation to the rise in energy prices and the difficult economic situation in our country. In work the analysis of existing implementations of “Smart home” and the Windows operating system. They had developed their own variant of implementation. The total amount of work is 69 pages, 27 figures, 3 tables,18 bibliographical references.

    Keywords: smart house, user interface, web-server, qt

    The work consists of:  69 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Manufacturing technology electromagnet crystalline products

    Author: Luzina Myroslava

    Group: РВ-22

    Supervisor: Senior Lecturer Popsui Vladimir Ilyich

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: In the thesis work considered the methods of manufacturing electromagnetic crystals (EC), namely, milling and photolithography. Experimental studies by photolithography and milling, determine the accuracy of obtaining topological figure picture on materials firm Rogers and flan. Also in the paper studied the effect of geometrical parameters, namely, the width of the microstrip conductor on frequency response (frequency response). Modeling response of EC – devices in the software product Mathcad. Recommendations on making ЕС devices and ensuring human life in terms of production.

    Keywords: electromagnetic crystals, milling, photolithography, mathematical model.

    The work consists of:  70 pages of explanatory note and 2 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Fiber-optic communication lines with wavelength division multiplexing

    Author: Stupak Vladyslav

    Group: РІ-21

    Supervisor: Demianenko Petro

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: The aim is to calculate the parameters of optical filters for multiplexing, demul-tiplexing processes signals in fiber-optic communication lines with spectral multi-plexing. The paper analyzes the impact of the filter parameters based on optical ring res-onator and conducted calculations depending transition fading between the input and output signals. The possibility of applying filters to form equidistantly grid frequen-cy, which allows using rezhektsiyni filter properties to improve the signal / noise ra-tio at the output filter. Calculations shoulders designs depending on the normalized frequency at dif-ferent coupling coefficients k and integral losses in the cavity αl. the value of attenua-tion in the passband nonlinear effects that occur when optical signal passing through lightguide. We describe the design and application of optical filters and optical am-plifiers. Showing generator design solitons. The paper discusses issues of health and safety. Results of work can be used in the design of digital networks Ukraine. Explanatory Note includes 82 pages of typewritten text. It uses 7 tables, 24 fig-ures, 44 formulas, 25 sources of scientific and technical literature, 3 applications.

    Keywords: nonlinear phenomena fiber, dispersion, circular resonator, an optical amplifier, an optical filter, soliton, wdm

    The work consists of:  82 pages of explanatory note and 3 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Modified simplex algorithm

    Author: Maksymets Denys

    Group: РВ-21

    Supervisor: Tarabarov Serhiy

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: Graduate work consists of 88 pages of explanatory note and includes 29 illustrations, 6 tables, 18 references and 4 applications. The aim of the thesis is to develop a modified simplex method of Nelder Mead algorithm and investigate the modifications using the set of functions of varying complexity. The thesis includes the analyzes of existing methods of optimization of order zero. The Neldera and Mead algorithm is investigated, its advantages and disadvantages are described. The algorithm Neldera and Mead is described. The modified algorithm was developed and described. The program for the graphical display of methods using C # programming language and technology of Windows Forms is described. A research of the modified method by the example of the five functions of varying complexity is completed. The results, which reflect the efficiency of the developed modifications are displeyed. The developed modification of Nelder Mead algorithm is recommended to use for optimize processes which are described by functions of several variables.

    Keywords: design, nelder mead algorithm, optimization

    The work consists of:  88 pages of explanatory note and 4 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Cooler water cooling for the computer system unit

    Author: Sakir Serhii

    Group: РВ-21

    Supervisor: PhD, doc. Demyanenko Petro

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: In degree project designed water cooling system for the computer system unit, PCB automatic fan speed of rotation regulator, constructional documentation with using modern element base was developed and the basic factors of safety and operation of the process, and ways to support them are considered. The aim of the project is to develop the design of the water cooling system as a part of the computer system unit. Explanatory Note (A4) contains 79 pages, 10 tables, 24 drawings 10 bibliographic names on the list of references 2 additions and necessary drawings: electrical block diagram of automatic fan speed of rotation regulator (A3 format), electrical schematic diagram of automatic fan speed of rotation regulator (A3 format), PCB drawings (A2 format), assembly drawing of the printing unit (A2 format), assembly drawings of cooler water cooling (A1 format), assembly drawings of water cooling system (A1 format) and specifications (A4 format) to these drawings.

    Keywords: water cooling system, printed circuit board, reliability, vibration and impact strength

    The work consists of  81 pages of explanatory note, 3 appendix and 6 drawings

    Explanatory note: Full text

    Drawings:

  • Стуктурна схема
  • Схема електрична принципова
  • Плата
  • Друкований вузол
  • Схема охолодження
  • Складальний кресленик
  • The microwave device for determining the moisture content of grain and other bulk materials

    Author: Rybachuk Anna

    Group: РБ-21

    Supervisor: Sidoruk Yuri Kondratievich

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: This work is presented in 93 pages, which contain 16 figures, 1 tables, 55 sources and 2 appendix. The aim of this project is to prepare theoretical data for microwave moisture meters and other bulk materials. The object of consideration is a device for determining the moisture content of grain, based on the use of cavity-method, using a computer. The subject of the work is to calculate the parameters of the resonator, and mathematical errors during measurements.

    Keywords: electromagnetic field, grain, exposure, resonator, waveguide, antenna, moisture, directional coupler.

    The work consists of:  93 pages of explanatory note and 2 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Signal processing algorithm fiber optic accelerometer

    Author: Matsveiko Mariyya

    Group: РБ-21

    Supervisor: Petro Demyanenko

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: The aim of this work is to develop signal processing algorithms fiber optic sensor (FOS) acceleration of the pulse intensity modulation optical flow. The work consists of four sections. In the first and second chapters deals with the principles and characteristics of semiconductor and fiber optic sensor acceleration. The third section is devoted to the creation besposeredno algorithm and its testing. Check algorithm and calculation results carried out by the environment of Mathcad. The results of calculations in tables. Since the algorithm are 2 forms of presentation of the results, it was an example of each of these forms In the fourth section deals with the problems of occupational health and safety in the use of computer and electrical appliances. Thesis completed in 84 pages containing 19 figures, 7 tables, 20 sources used and 2 applications.

    Keywords: аcceleration, fiber optic sensor, pulse

    The work consists of:  84 pages of explanatory note and 2 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Capacitive accelerometer

    Author: Kompel Maryna

    Group: РВ-22

    Supervisor: Volodimir Kapelushnyi

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: The aim of this work is to develop a mathematical model of capacitive accelerometer. Object: capacitive accelerometer. Subject: modeling principle of capacitive accelerometer. The work consists of 6 chapters in which various types of accelerometers (such as beam, piezoelectric, thermal, tensoresistive) were examined, principle of work was analyzed, and the comparison leading manufacturers’ parameters of accelerometers was given. Mathematical models for two types of capacitive accelerometers were created. The problems of health and safety at work were considered. Thesis performed on 60 page containing 24 illustrations, 4 tables, 13 used sources and 2 applications.

    Keywords: micromechanical systems, sensor, accelerometer, mathematical model, acceleration.

    The work consists of:  60 pages of explanatory note and 2 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Pulse induction metal detector

    Author: Marynich Andrii Grigorovich

    Group: РВ-21

    Supervisor: Kapelushniy Vladimir Danilovich

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: The degree project consists of an explanatory note on 88 pages, includes 17 illustrations, 13 tables, 4 drawings, 25 links, 2 appendices. The purpose of the degree project is the development board microprocessor metal detector, which is designed to find metal objects: the construction or repair, the security structures in the treated wood industry, searching for suspicious objects in the soil, archaeological excavation, etc. The project analyzed the modern types of metal detectors and methods by which these devices operate. Studied counterparts, the optimum base element and select the most effective technical solutions. Based on the data PCB designed, selected the required components. The calculations proving the efficiency and compliance with all regulations and standards.

    Keywords: keywords: metal detector , pulse induction, microcontroller, pcb(printed circuit board), control unit.

    The work consists of  86 pages of explanatory note, 4 appendix and 5 drawings

    Explanatory note: Full text

    Drawings:

  • Схема електрична принципова
  • Друкований вузол складальний кресленик
  • Котушка складальний кресленик
  • Схема структурна принципова
  • Друкована плата
  • Signal processing algorithms contactless measurement of glucose based on Arduino microcontroller

    Author: Kanshyna Hullier Paltashivna

    Group: РБ-21

    Supervisor: Bogomolov Mykola Fedorovich

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: The work developed signal processing contactless measuring glucose in human blood. For algorithm created by the program ( programming language C ++, environment Arduino 1.6.9), which manages microcontroller Arduino, handles signals and displays the results on the screen of the personal computer or on the LCD – display. The calculations proving the efficiency of the device. The experimental results are compared with blood glucose meter is based on electrochemical methods of analysis. Experimentally proved that the device is reliable in detecting glucose in addition to the invasive method. The problems of labor protection and safety in the operation of the device.

    Keywords: glucose, express – analysis, blood, non-invasive.

    The work consists of:  85 pages of explanatory note and 6 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Device to amplify the sound of the bandura

    Author: Kulyk Viktoriia

    Group: РВ-21

    Supervisor: Adamenko Julia

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: Explanatory note diploma project on "device for sound reinforcement bandura" volume 56 pages contains 24 illustrations, 8 tables, 2 addition and 7 applications bibliographic titles for references. The aim of the diploma project is to develop a portable device pickup and sound reinforcement bandura, to ensure the functioning tures which do not need to interfere with the design tool. The project analyzed the design bandura and methods of removing the sound of acoustic instruments selected optimum pickup and circuit gain with frequency compensation scheme of electrical structural and fundamental instrument, designed PCB and printing unit and conducted calculations confirm performance of the device, including: reliability, mechanical testing. In the section "Occupational Safety" is estimated major potentially harmful and dangerous factors that play a role in the design, manufacture and operation of the designed device.

    Keywords: bandura, pickup, piezoelectric, power, printed circuit board.

    The work consists of  58 pages of explanatory note, 2 appendix and 5 drawings

    Explanatory note: Full text

    Drawings:

    Automatic lighting control module manufacturing and residential premises

    Author: Sharai Alla

    Group: РІ-21

    Supervisor: Ph.D. Associate Professor Leonid Dyuzhayev

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: The degree project consists of an explanatory note on 89 pages, includes 26 illustrations, 23 tables, 3 drawings, 19 links, 3 appendices. The purpose of the degree project is to develop of automated lighting control module household and industrial facilities to reduce power consumption and save natural resources. The project analyzed requirements of modern energy savings. Analogs are investigated, optimum element base is picked up and the most effective technical solutions are chosen. It is designed the printed circuit board of automated lighting control based on research data, the required components are chosen. The calculations confirming operability of the device and compliance to all normative documents and standards are carried out. The developed for automated lighting control module is available for use in any residential and industrial premises.

    Keywords: automated lighting control module, microcontroller, printed circuit board, arduino nano, motion sensor, light sensor

    The work consists of  89 pages of explanatory note, 3 appendix and 4 drawings

    Explanatory note: Full text

    Drawings:

  • Схема електрична принципова
  • Друкована плата
  • Друкований вузол
  • Презентація
  • The device for measuring heart rate rights

    Author: Sanko Olena

    Group: РБ-21

    Supervisor: Demianenko Petro

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: The purpose of this degree project is to develop pulse, which with high accuracy can measure the pulse of the person. The project consists of six sections. In the project considered the following principles: Measure heart rate by using the photodiode; Data processing using microcontroller. The device has the following advantages: small power consumption, small size, low cost and possibility of use directly in sports. Thesis project performed at 84 pages, and contains 13 tables, 10 figures, 20 of the used sources, 4 appendices, 3 drawing, 3 poster.

    Keywords: heart rate meter, microcontroller

    The work consists of  84 pages of explanatory note, 4 appendix and 3 drawings

    Explanatory note: Full text

    Drawings:

  • Схема електрична принципова
  • Друкована плата
  • Складальне креслення
  • Desulfator car batteries

    Author: Korzh Anatoliy

    Group: РВ-22

    Supervisor: Popsui Volodymer

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: Thesis project on “Desulfator car batteries” developed for practical verification of the possibility of recovery of acid car batteries. In the design process the analysis of the causes of sulfation, means of prevention and recovery of batteries. The selected circuit diagram, designed and manufactured the layout of the device, checked that it is working.

    Keywords: desulfator, sulfation, battery

    The work consists of  60 pages of explanatory note, 3 appendix and 8 drawings

    Explanatory note: Full text

    Drawings:

  • Схема електрична структурна
  • Схема електрична принципова
  • Друкована плата
  • Друкований вузол
  • Трансформатор
  • Радіатор
  • Шайба
  • Складальний кресленик
  • Modern laboratory techniques characteristics of blood

    Author: Lutchenko Maksim

    Group: РБ-21

    Supervisor: Sydoruk Yurii

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: The purpose of the given work is the analysis of existing methods and improving them by computer obrodky. The work consists of five chapters. The first chapter introduces the features Scud blood. The second is devoted to analysis of existing methods to study the characteristics of blood. The third section describes the computer image processing. In the fourth section, the algorithm of counting blood elements formennyh environment using MatLab. The calculation results are invoked as images. In the fifth chapter deals with the problems of occupational health and safety in the use of computer and electrical appliances.

    Keywords: laboratory diagnostics, blood, computer image processing

    The work consists of:  105 pages of explanatory note and 0 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Research of electromagnetic waves in biological objects

    Author: Klimuk Oleksandr

    Group: РБ-21

    Supervisor: Bogomolov Mykola

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: The aim is to develop a computer model of the electromagnetic radiation propagation in biological objects. Analyzed the existing mathematical model of the electromagnetic radiation propagation in biological objects. The dependence of the modeling error of Monte Carlo. Modeled propagation of laser radiation in a model, has the optical properties of the epidermis. The problems of health and safety. Thesis consists of 4 sections and is made of 76 pages containing 18 illustrations, 2 tables, 14 sources used, and 3 applications

    Keywords: radiation computer model, the monte carlo method

    The work consists of:  79 pages of explanatory note and 3 appendix

    Explanatory note: Full text

    Drawings:

    Презентація

    Control unit for data collection module laser diagnostic system

    Author: Snisar Anton

    Group: РБ-21

    Supervisor: Golovnya Victoria

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: The aim of the work is to develop a control unit for data collection module of laser diagnostic system. The work consists of 5 sections. Existing methods and devices for diagnostic blood parameters. In the project was developed structural and electrical schematic diagram of the control unit and a trace of the PCB. The analysis of reliability, efficiency and adaptability of the control unit. The problems of health and safety in emergency situations was reviewed. Thesis completed in 67 pages containing 9 figures, 13 tables, 11 sources used, and 5 applications

    Keywords: laser, engine, microcontroller, atmega8, usb-uart, diagnostic system, blood

    The work consists of  67 pages of explanatory note, 5 appendix and 4 drawings

    Explanatory note: Full text

    Drawings:

  • Структурна схема
  • Електрична принципова схема
  • Друкована плата
  • Друкований вузол
  • Magneticlaser therapy device for the treatment of urological diseases

    Author: Stuparenko Anastasiia

    Group: РБ-21

    Supervisor: Bogomolov Mykola Fedorovych

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: The aim of work is to develop new therapeutic magnetic-laser system for treatment at home. The work consists of 4 parts. Analyzed existing methods and devices for the treatment of inflammation of the prostate. The parameters, the size and characteristics of the electromagnet been calculated. The scheme of supply of laser radiation directly to the prostate gland. Calculated thermal conditions of electromagnetic heating element. The problems of occupational health and safety.

    Keywords: magnet, laser therapy, inflammation of the prostate

    The work consists of:  76 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Remote control module for mechanical devices

    Author: Chebotarskyi Dmytro

    Group: РІ-21

    Supervisor: Ph.D. Associate Professor Leonid Dyuzhayev

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: The degree project consists of an explanatory note on 72 pages, includes 14 illustrations, 16 tables, 2 drawings, 14 links, 2 appendices. The purpose of the degree project is the operating payment development of the remote control module for mechanical devices. The project analyzed the requirements for modern remote control technologies. Analogs are investigated, optimum element base is picked up and the most effective technical solutions are chosen. It is designed the printed circuit board of remote control module based on research data, the required components are chosen. The calculations confirming operability of the device and compliance to all normative documents and standards are carried out. The developed remote control module is recommended to be used in all mechanical device which needed remote control and will be used in wide masses.

    Keywords: remote control module for mechanical device, microcontroller, printed circuit board, control unit, transmitter, receiver, smartphone with operating system android.

    The work consists of  72 pages of explanatory note, 3 appendix and 3 drawings

    Explanatory note: Full text

    Drawings:

    The modified test method steps

    Author: Pyatov Sergii

    Group: РВ-21

    Supervisor: Tarabarov Sergii, docent

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: Explanatory note with a volume of 74 pages contains 9 illustrations, 8 tables, 5 additions and 9 bibliographic items on the link list. The work presents development of a modification of the trial steps method, and create a research program in the programming language "C". Numerical results of several functions, both classic and modified method of trial steps. A comparison of these methods with certain parameters, such as depth of search, number of iterations and calculations. The result is a software implementation of the modified method of trial steps.

    Keywords: search, extreme, minimum, point , step

    The work consists of:  74 pages of explanatory note and 5 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Simulation of analog integrated circuits using the package microcap – 9

    Author: Ozirnyi Sergii

    Group: РВ-21

    Supervisor: Pryschepa Mykola

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: Thesis: “Simulation of analog integrated circuits using the package MicroCap – 9″ includes: 79 pages, 23 figures, 16 tables and two appendices. The work is addressed to the following questions: Analysis of schematic solutions with current trends of microcircuitry; Developed schematics of analog integral circuit based on analysis; Created electronic models of developed analog microcircuits and its cascades using the package MicroCap – 9; Research the functioning of main parts and microcircuit in general and analysis of main parameters of developed microcircuit. As the initial in selected methods of analysis and calculations were taken Gummel-Pun transistor models.

    Keywords: analog integrated microcircuit, gummel-pun model, differentional amplifier

    The work consists of:  80 pages of explanatory note and 2 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Optimization of Newton’s method for finding roots of equations circuit

    Author: Zubko Olexii

    Group: РВ-21

    Supervisor: Tarabarov Sergii, docent, PHd

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: Thesis for the degree of Bachelor on “Optimization of Newton’s method for finding roots circuit functions” contains 94 pages, 11 figures, 10 tables and two appendices. The paper: 1. Analysis of existing methods for finding roots of power functions; 2. The modified calculation algorithm based on the classic roots of Newton; 3. A website that sells a type of software algorithm; 4. investigated and the results of classic metal-modified method. The basis of web site taken technology HTML5 platform and content management system WordPress.

    Keywords: optimization, newton, roots, circuit function, search

    The work consists of:  94 pages of explanatory note and 2 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    The calculation of the main parameters of single-mode optical fiber

    Author: Denysenko Roman

    Group: РВ-21

    Supervisor: Demyanenko Petro

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: The work is devoted to study the main parameters of single-mode optical fiber, in particular, calculate chromatic dispersion for different concentrations of impurities in the materials of the core and shell. The work consists of four sections. Analyzed the main elechrominance characteristics of optical fibers as physical sulphurdovima of information transfer. Implemented the calculation of key parameters ditch single-mode optical fiber, in particular, the calculation of chromatiction of dispersion for different concentrations of impurities in the materials of the core and about lonky; the results are relatively. The problems of occupational health and safety in the use of personal computer.

    Keywords: single-mode optical fiber lightguide, refractive index profile, numerical aperture, normalized frequency, dispersion, attenuation.

    The work consists of:  87 pages of explanatory note and 4 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Protection against corrosion

    Author: Skliarenko Yevhenii

    Group: РВ-21

    Supervisor: Senior Lecturer Andriy Novosad

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: In this diploma project has developed a corrosion protection system. The project consists of. Was developed electrical circuit schematic and design of the device, selected element base. The calculations confirming the performance of the device. The problems of occupational health and safety in the establishment and operation of the device. Diploma project completed 50 pages, seven sections, containing 8 figures, 6 tables, 16 sources used and applications.

    Keywords: corrosion, corrosion, corrosion protection system

    The work consists of  50 pages of explanatory note, 3 appendix and 5 drawings

    Explanatory note: Full text

    Drawings:

  • Структурна схема
  • Схема з’єднань
  • Схема електрична принципова
  • Складальний кресленик
  • Плата друкована
  • Adapter alarm with gsm communication channel

    Author: Khlobystin Serhiy

    Group: РВ-22

    Supervisor: Dmitry Evhrafov

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: The degree project consists of explanatory notes of 55 pages, including 18 figures, 10 tables, 4 draftsmanships, 11 references, 2 applications. The aim of this project is to develop security alarm adapter with GSM communication channel. The main purpose of this device is to form an alarm signal for cell phone. The project includes a graphical documentation, which includes: draftsmanship of scheme of electric concept, draftsmanship of printing unit, draftsmanship of PCB, draftsmanship of unit. The developed device is recommended to be used at home.

    Keywords: gsm, alarm, adapter security system, security.

    The work consists of  56 pages of explanatory note, 2 appendix and 5 drawings

    Explanatory note: Full text

    Drawings:

    Portable charger

    Author: Tupitsyn Nikolay

    Group: РВ-22

    Supervisor: Popsuy Vladimir

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: In this thesis project was developed portable charger for mobile phones and other devices. A modulation scheme of electric concept among Multi-Sim. The calculations for the design of the PCB, the calculation of the vibration, reliability; recommendations for safety. Made layout portable charger and verified its performance. Diploma project includes __ pages of explanatory notes, illustrations __, __ tables, drawings __, __ bibliographic titles.

    Keywords: dc-dc converter, charge, se elements.

    The work consists of  65 pages of explanatory note, 9 appendix and 6 drawings

    Explanatory note: Full text

    Drawings:

    Development spark generator technology for electrosurgery

    Author: Yaremenko Andrii

    Group: РВ-22

    Supervisor: Ph.D., professor Yanenko Alexey

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: In degree work the development of spark generator for electrosurgery technology, PCB of spark generator was designed and constructional documentation with using modern element base was developed. Chosen design decisions regarding internal and external configurations. Also, the calculations PCB in shock and vibration durability and reliability calculation device according to specifications. The original spark generator junction formation of radio pulses. Create a basic set of drawings, which give a general and comprehensive picture of the placement and operation of the device. Thesis project performed at 66 pages, and contains 9 tables, 8 figures, 11 of the used sources, 3 appendices.

    Keywords: spark generator, electrosurgery, duty cycle, high-frequency pulses

    The work consists of  66 pages of explanatory note, 3 appendix and 5 drawings

    Explanatory note: Full text

    Drawings:

    Аutomatic control street lighting

    Author: Babych Oleksandr Viktorovych

    Group: РВ-22

    Supervisor: Sydoruk Yurii Kindratovych

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices 172 Telecommunication and radio engineering)

    Summary: The diploma paper consists of explanatory note for 65 pages, it includes 5 illustrations, 14 data tables, 4 drawings, 23 references, 2 annexes. The object of the diploma project is the construction of automatic device which controls street lighting with ability to turn it on and turn it off according to natural lighting. As a result there were found different circuitry solutions for these devices. Electronic scheme was chosen, required elemental base was selected for the device. Method of producing the board was selected. Calculation of printed assembling was carried and printed-circuit board was engineered. Calculations which prove efficiency of the device were proceeded. The device is recommended to use for the lightning of a cottage area, streets, parks or landscape compositions.

    Keywords: keywords: automatic device, lighting, printed-circuit board, light-dependent resistor, relay.

    The work consists of  65 pages of explanatory note, 4 appendix and 4 drawings

    Explanatory note: Full text

    Drawings:

  • Схема електрична принципова
  • Друкована плата
  • Автомат керування вуличним освітленням. Складальний кресленик.
  • Автомат керування вуличним освітленням. Складальний кресленик.
  • Lang disease diagnostics by means of computer`s tomography

    Author: Sachik Kateryna

    Group: РБ-21

    Supervisor: Golovnia Viktoriia

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: The main goal of the thesis is to provide the oretical data for tomographic pulmonary disease research and tomographic image reconstruction. The work consists of four sections. The methods of computed tomography were analysed. The characteristics of computer-tomographic images were examined. Mathematical reconstruction of images and its processing were examined using software implementation (C programming language). The size of the investigated object and doses with computerized tomography of the lungs were calculated. The problems of occupational health and safety in the use of computer tomography were considered. Thesis completed in 97 pages containing 43 figures, 12 tables, 15 sources used and 2 applications.

    Keywords: computed tomography, diagnostics, lungs.

    The work consists of:  97 pages of explanatory note and 2 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Video recording system with integrated motion sensor

    Author: Mohyr Olexii

    Group: РВ-41с

    Supervisor: Duzhaev Leonid

    ELK: Specialist

    Speciality: 7.05090201 Radioelectronic Devices and Facilities

    Summary: In this diploma project video recording system with integrated motion sensor aiming to protect objects was developed. The project aims to create additional circuit that will control digital video recorder the signal from the sensor movement. The design is fully compliant with the specification, confirming the mentioned above calculations. The emphasis in the design was made to achieve a minimum cost to ensure the competitiveness of the device while maintaining all the specified parameters.

    Keywords: videorecording, motion sensor, videorecording system

    The work consists of  103 pages of explanatory note, 4 appendix and 6 drawings

    Explanatory note: Full text

    Drawings:

    Unit for measurement of residual voltage

    Author: Velyhorskyi Vitalii

    Group: РВ-41с

    Supervisor: Domnich Volodymyr

    ELK: Specialist

    Speciality: 7.05090201 Radioelectronic Devices and Facilities

    Summary: In this diploma project the unit for measurement of residual voltage was developed. Electrical circuit schematic design of the device was developed and the rationale decisions for design were taken. The calculations confirming the performance of the device. The emphasis in the design was made to achieve a minimum cost to ensure the competitiveness of the device while maintaining all the specified parameters.

    Keywords: residual voltage, charged capacitor

    The work consists of  108 pages of explanatory note, 4 appendix and 11 drawings

    Explanatory note: Full text

    Drawings:

    Software and hardware method radiometric studies

    Author: Shpilin Oleg

    Group: РБ-31м

    Supervisor: Peregudov Sergii

    ELK: Master

    Speciality: 8.05090204 Biotechnical and Medical Equipment and Systems

    Summary: Master's thesis, 111 p., 32 fig., 13 tab., 1 appendix, 29 sources. Background. Measurement of low radiation of biological objects is a difficult process because the input level in most cases comparable with its own noise radio-metric system. Known methods and means have certain drawbacks, including low accuracy and lack of visibility of research results. The creation of software and hard-ware tools processing method for radiometric measurement of own radiation of bio-logical objects is the actual task. The purpose of the study. The aim of the thesis is to improve the research process radiometric electromagnetic properties of biological objects in the millimeter range. Object is electromagnetic radiation of biological objects in the millimeter wavelength range. The subject of research is the processing of electromagnetic signals in bio-logical objects radiometric system of mm range. Research methods, techniques and theory circles computer design – a model when developing and processing signals in radiometric studies of biological objects; methods of the theory of differential calculus and mathematical statistics – for the processing of measurement results; radiometry methods – to study the electromagnet-ic properties of biological objects. Theoretical and practical significance of the results: 1) A simulation model of the hardware and software signal processing in the low block radiometric system software using LabVIEW. 2) The method of evaluation of basic parameters of the transmission line that connects the output radiometric system computer. 3) Improved radiometric method studies of biological objects of low natural radiation in the microwave range.

    Keywords: radiometric system, biological objects, error measurement

    The work consists of:  111 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Measuring the speed of sound in liquids

    Author: Fedorenko Igor Vyacheslavovich

    Group: РБ-31м

    Supervisor: Movchanyuk Andriy Valerіyovich

    ELK: Master

    Speciality: 8.05090204 Biotechnical and Medical Equipment and Systems

    Summary: Subject matter of the study – liquids. Scope of the study – the speed of sound in liquids. Objective of the study – to modify pulse method with the ability to obtain data on the speed of sound in terms of strong acoustic interference. The first chapter of master’s degree work covers the importance of a priori knowledge of the speed of sound in liquids, as well as the basic methods of measurement. The multifrequency pulse method for measurement of the speed of sound in liquids was proposed. The objective and tasks of the study were formulated. The possibility of using piezoelectric circular ring transducers for both thickness and flexural vibration forms was shown based on the results of mathematical modeling in the second chapter of the work. Mathematical modeling of the distribution of sound pressure in the measuring chamber showed that adequate measurement results may be obtained only in case of flat wave front. As a result of mathematical modeling, the expression for calculation of the critical radius of measuring chamber was acquired. The requirements for individual functional units of the measurer of the speed of sound were presented in the third chapter of master’s degree work. The modeling and design of the measurer units were performed. The model sample of measurer of the speed of sound in liquids that implements the multi-pulse method was manufactured. The measured values of the speed of sound in liquids, which match the reference values with sufficient accuracy, were shown in the fourth chapter of the work. The expediency of the measurements using frequencies below the critical frequency of thickness resonance of the piezoelectric transducer was proved. The potentiality of the proposed method of measurement of the speed of sound in terms of interference concentrated in spectrum was shown.

    Keywords: speed of sound, multifrequency, pulse, ultrasound, piezoelectric transducers

    The work consists of:  147 pages of explanatory note and 3 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Modulation radiometric measuring assembly of absorbed energy dose during phototherapy

    Author: Lisnichyk Anatoliy Sergiyovuch

    Group: РБ-31м

    Supervisor: Yanenko Oleksii

    ELK: Master

    Speciality: 8.05090204 Biotechnical and Medical Equipment and Systems

    Summary: Magister’s dissertation: 105 p., 30 Fig., 3 table., 26 sources. Object of research – methods of measuring the dose absorbed energy in light therapy. Purpose – to improve the accuracy of the luminous intensity along with the simplification of the scheme and increased sensitivity. Research methods – used in the computer modeling of propagation of optical radiation, the electronic package "Mathcad 15" using the Monte Carlo method. Methods of Mathematical Statistics processing results, the laws optical distribution visible light. Under the influence of light on the human optical range appear certain effects depending on the wavelength. In medicine uses the whole range of optical radiation for phototherapy. The essential task is to analyze modern equipment for measuring optical radiation in phototherapy, identify gaps and develop tasks to eliminate them. Holding modeling of light radiation and experimental study of light penetration in biological tissues. Developing a model channel modulation of light passing through biological tissues for combined impact. Master's thesis on materials published 2 abstracts at scientific and technical conferences, articles in professional journals and received one patent for utility model.

    Keywords: modulation radiometr, light, intensyvnivst waves.

    The work consists of:  106 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Suprasonic diagnosis of the frontal and millixary sinuses

    Author: Yevtushok Vadym Viktorovich

    Group: РБ-31м

    Supervisor: Demianenko Petro

    ELK: Master

    Speciality: 8.05090204 Biotechnical and Medical Equipment and Systems

    Summary: Master's thesis: 85 p., 28 fig. 6 Table. 1 Additionally, 27 sources. Object of research – methods of ultrasonic diagnosis of diseases of the frontal and maxillary sinuses. Subject of research – more informative ehozobrazhen obtained in A-mode operation. Purpose – is to improve the quality of ultrasound diagnostics conducted by the Assisted synuskopa in the A-mode, parameters pyezoperetvoryuvacha by improving and increasing the depth of penetration of ultrasound. Research methods – computer modeling in software package MATHCAD. The obtained results give an opportunity to increase the information content ehozobrazhen. As a result of analysis of the ultrasonic device, the theoretical analysis of possible structures Piezoelectric transducer may develop a broadband transducer echo.

    Keywords: suprasonic, sinusitis, piezoelectric transducer, echoimage.

    The work consists of:  90 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Signal processing nanoelectronic devices

    Author: Khatyan Dmytro

    Group: РІ-31м

    Supervisor: Doctor of Engineering, Professor, Nelin Eugene

    ELK: Master

    Speciality: 8.05090203 Intelligent Technologies of Microsystems Radio Electronic Engineering

    Summary: Volume explanatory note is 100 pages, which includes 4 sections, 50 illustrations, 2 annexes and 48 names on the list of bibliographical references. Actual research questions of devices based on artificial carbon structures. The purpose of the study was to devices based on synthetic allotropic forms of carbon: modeling and analysis features. The existing signal processing devices, defined their advantages and disadvantages. Investigated the formation of the band diagrams of semiconductor superlattice. As a result of the analytical literature review, scientific, technical articles and electronic sources received opinion on devices that run on synthetic allotropic forms of carbon. The software that implements a mathematical model. Characteristics of typical devices and conducted their analysis.

    Keywords: fullerene and devices based on it, carbon nanotubes and devices based on them, and graphene devices, based on artificial allotropic forms of carbon, signal processing devices, superlattice, impedasn model periodic structures.

    The work consists of:  108 pages of explanatory note and 2 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Synthesis of frequency selective devices based on electromagnetic crystals

    Author: Onischenko Dmytro Yurijovich

    Group: РІ31м

    Supervisor: Adamenko Yuliia

    ELK: Master

    Speciality: 8.05090203 Intelligent Technologies of Microsystems Radio Electronic Engineering

    Summary: Statement of master’s thesis: 103 p., 37 fig., 4 tab., 2 applications, 25 sources. The object of study – devices based on electromagnetic crystals. Purpose – to study the synthesis filter algorithm based on electromagnetic crystals. Research method – impedance method and CAD modeling of microwave equipment. Today the highest efficiency filters for use in the microwave range (based on microstrip lines) with three-dimensional heterogeneity. They also can make the device more compact filtration through a combination of heterogeneity in one of several equivalent circuit elements prototype filter. Currently there are no strict solution synthesis problem for either individual or irregularities, especially for devices based on them. As a result of work performed impedance adaptation suited to the synthesis filter based on electromagnetic crystal. The simulation, which confirms the adequacy of the algorithm. Made forecasted assumption that the directions of further improving the efficiency of irregularities.

    Keywords: electromagnetic crystal, microstrip line impedance model, line heterogeneities transmission.

    The work consists of:  103 pages of explanatory note and 2 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Development of microsatellite traffic control system and protect it from external influences in space

    Author: Ivanov S.L.

    Group: РІ-31м

    Supervisor: Uvarov B.M.

    ELK: Master

    Speciality: 8.05090203 Intelligent Technologies of Microsystems Radio Electronic Engineering

    Summary: Volume explanatory note is 133 pages that include 4 sections, 59 illustrations, 2 applications and 81 items on the list of bibliographic references. Two main areas: active triaxial orientation and methods of protection from cosmic factors. The objects of study of this master’s work is the space launch systems and protection of on-board equipment and radioelektronoyi of the spacecraft in outer environment. The purpose of the master’s work performance is choosing the most optimal method of satellite control and ensure functional safety of electronic means and space systems, including spacecraft that will increase the term of active existence created spacecraft from 10-20 years or more. As a result of the analytical literature review , scientific, technical articles and electronic sources received opinion on targeting systems , and methods to protect the satellite. Mathematical models of traffic control and the resulting value calculation protective surface protection systems of the satellite.

    Keywords: satellites, system orientation, protection systems, grapheme, composite.

    The work consists of:  133 pages of explanatory note and 2 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Antennas based on the three-dimensional inhomogeneities for telecommunication technologies

    Author: Korniichuk M.

    Group: РІ-31м

    Supervisor: Nazarko A.

    ELK: Master

    Speciality: 8.05090203 Intelligent Technologies of Microsystems Radio Electronic Engineering

    Summary: Master dissertation, 105 p., 71 fig. 3 tab., 1 application, 32 source. Object of research — electromagnetic crystals and structures based on them. Subject of research — based three-dimensional antenna electromagnetically crystal irregularities. Purpose of work — the use of three-dimensional electromagnetic-crystal inhomogeneities in the structure of the antenna Wi-Fi range to improve performance antennas. Research methods – the method of finite integrals, numerical method of three-dimensional electromagnetic analysis method Periodic transmission line model method of lumped elements. The work was considered modern microstrip antenna solutions and structures that improve the characteristics of microstrip antennas, including two-dimensional and three-dimensional structure structure. Special attention is paid to the introduction of three-dimensional structures in antenna technology. Done and analyzed a mathematical model using three-dimensional antenna structures. The influence of the dependence of the effective dielectric constant of the material foundations of the characteristics of the antenna devices. The results of research allow to significantly improve the characteristics of antennas, namely, to significantly increase the coefficient of reflection, to extend the working bandwidth increase antenna gain and reduce its size. As this topic is very relevant today, the results of this study can be used in further research.

    Keywords: microstrip antenna, dgs, periodic structure, electromagnetic crystal, electromagnetically crystal irregularities

    The work consists of:  105 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Resonans frequency-selective structures based on the electromagnetocrystalline inhomogeneities

    Author: Gulenko Oleksii Vadimovich

    Group: РІ-31м

    Supervisor: Nazarko Anatolii Ivanovich

    ELK: Master

    Speciality: 8.05090203 Intelligent Technologies of Microsystems Radio Electronic Engineering

    Summary: Master dissertation: 107 p., 71 fig., 7 tab., 3 applications, 33 sources. Object of research — electromagnetocrystalline inhomogeneities and structures based on them. Subject of research — narrowband filters based on EC-inhomogeneities. Purpose of work — the usage of three-dimensional electromagnetocrystalline inhomogeneities in the structure of narrowband filters of Wi-Fi range. Research methods — the method of nonuniform transmission line, the method of finite integrals. In our work we analyzed such aspects as the traditional and modern microstrip solutions that improve the characteristics of frequency-selective microstrip devices, including the inhomogeneity in the ground layer (defected ground structure, DGS) and the conductor layer (defected microstrip structure, DMS). Special attention was paid to periodic microstrip radio structures. We also examined the building of the narrow-band filters based on these technologies. In our research we carried out the analysis of Wi-Fi technology and requirements for the filters construction in this range according to the international standards and typical analogs of Wi-Fi range filters. A single and three-dimensional computer models of narrow band filters based on Fabry-Pero models using EC-inhomogeneities were devised and their properties in a number of computer experiments were investigated. We analyzed the impact of the dependence of the effective dielectric constant of the material basis on the filter characteristics and showed the importance of its incorporation. The impact on the raid phases during races impedances in the structures of EC-filters was also studied and taken into consideration. The results can be used for the further scientific research and educational process in educational institutions of Ukraine.

    Keywords: resonators, electromagnetic crystal, mictrostrip device.

    The work consists of:  107 pages of explanatory note and 3 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Analysis of electromagnetic fields diffuser with fractal geometry indoors

    Author: Tkach Leonid

    Group: РВ-31м

    Supervisor: Zinchenko Maxim

    ELK: Master

    Speciality: 8.05090201 Radioelectronic Devices and Facilities

    Summary: Master dissertation devoted to issues considering the level of radiation of electromagnetic fields on diffusers with fractal geometry. Explanatory note occupies a volume of 128 p., Includes 45 figures, 18 tables, 144 formulas and 44 sources. It consists of an introduction, list of references, five chapters, conclusions, list of references and applications. In the master’s dissertation printed circuits and devices considered as diffusers of fractal geometry. A model сonductors PCB antenna structure as random stochastic fractal dendritic type. Made by modeling electrodynamic systems devices approximation of thin conductors and flat screens that take into account the calculation of the surface current induced excitation leading to cell model. As a mathematical basis is the method of integral equations written on the surface current density in conductors and conductive thin screens. The investigation of fractal antennas range from 2 to 18 GHz, which show that their work area frequency bandwidth is interleaved and relaxation. Bandwidth increases with increasing operating frequency of the antenna. In bandwidth excited some local areas active surface fractal antenna. The size and location of these areas depend on the frequency of the probe signal. Fractal antenna in certain frequency bands can provide enough high gain. Experimentally confirmed that the circuit boards in evaluating their EMC can be considered as fractal fertilizer.

    Keywords: electromagnetic compatibility, the level of radiation of electromagnetic fields, statistical and deterministic approach

    The work consists of:  116 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Program to improve the quality of services e-commerce using mobile devices

    Author: Tarashscuk Hryhorii

    Group: РВ-31м

    Supervisor: Levandovskii Vitalii

    ELK: Master

    Speciality: 8.05090201 Radioelectronic Devices and Facilities

    Summary: Master dissertation: 128 p., 12 fig., 2 tab., 1 applications, 30 sources. Object of research — a multimedia smartphone IPhone. Subject of research — methods of programming in Xcode. Purpose of work — to reduce the number of returns in the online purchases through mobile devices. Development of the program will provide new opportunities for users mobile operating system. This program provides significant advantages over existing analogues.

    Keywords: programs, iphone, xcode

    The work consists of:  135 pages of explanatory note and 0 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Analysis and synthesis ukrainian speech

    Author: Minnigalimov Ruslan

    Group: РВ-31м

    Supervisor: Tarabarov Sergii

    ELK: Master

    Speciality: 8.05090201 Radioelectronic Devices and Facilities

    Summary: Urgency. Ukrainian is the state language and mother tongue of our people. One of the important components of language is intonation. It conveys the meaning of speech, expresses the attitude of the speaker to what is said, and provides emotional expression values play an important role in speech and at the same time is less explored. Research conducted intonation philologists, linguists. They describe its characteristics and types, such as ascending or descending intonation, but from a technical point of view, these descriptions are no specifics, so it is important to study the characteristics of the speech signal tone and their descriptions to provide measurement capabilities. The purpose and objectives of research. The aim of this work is to study the characteristics of the speech signal tone, methods of analysis of these characteristics and their description of this method to provide design values with which you can be granted a more accurate description of intonation. Object is Ukrainian intonation of speech that is written in the speech signal. The subject of the study is the frequency of the fundamental tone of the speech signal, spectrogram and its intensity. Methods. We study the characteristics of the speech signal, frequency spectrogram basic tone and speech signals. Study occur when changing the tone, its types: smooth, interrogative and such that speech gives a negative value. Its parameters: frequency of basic tone, spectrogram, intensity. Scientific novelty of the results of the master’s thesis is as follows: 1. The dependence of the fundamental tone frequency, intensity and spectrogram signal related to the Ukrainian intonation of speech. 2. Made mathematical calculation frequency change basic tone signal. The practical significance. Mathematical calculation frequency change basic tone will more accurately describe the speech signals when examined intonation to help better understand the dependence of the frequency of the fundamental tone of tone and intonation better establish links with such characteristics as spectrogram and signal intensity. The structure of the thesis. The thesis consists of an introduction, three chapters, the last of which includes conclusions on the study, list of sources. The total volume of 90 pages.

    Keywords: speech analysis, speech synthesis, mathematical model

    The work consists of:  107 pages of explanatory note and 3 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Investigation of service parameters of terrestrial and airborne receivers GPS

    Author: Maksimenko Yarslav

    Group: РВ-31м

    Supervisor: Pryshchepa M. M.

    ELK: Master

    Speciality: 8.05090201 Radioelectronic Devices and Facilities

    Summary: Master dissertation: 93 p, 13 fig., 23 tab., 20 sources. Subject:” Investigation of service parameters of terrestrial and airborne receivers GPS”. Research object: pseudorange model to the satellites GPS. Simulated and studied model pseudorange satellites; pseudorange measurement methods; factors affecting the error vimyru psevdodalnosti. The technique of pseudo-range measurements; pseudo formats in the navigation receiver; Decoding measurement information. And performs decoding processing receiver data in the time interval 8000 seconds. MatLab program for determining visibility of satellites, decode processing of the experimental data and the results of measurements.The methods for the management of safety in air navigation system, the introduction of a satellite navigation system.

    Keywords: pseudo-range, satellites, gps, orbit, modeling, interpolation, decoding, influence factors, research, message structure.

    The work consists of:  93 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Adaptive surge protector to protect information in the means of computer technology

    Author: Ishscenko Kostiantyn

    Group: РВ-31м

    Supervisor: Yevhrafov Dmytro

    ELK: Master

    Speciality: 8.05090201 Radioelectronic Devices and Facilities

    Summary: In this master’s thesis was a study of information leakage in the line supply side due to electromagnetic radiation of the scheme canal network adaptive filter. Was developed electrical schematic diagram of an adaptive network filter. This active power filter creates a high resistance, serial line harmonic current. With high power of the source, passive filter absorbs harmonic currents generated by nonlinear load. This filter can be used in any area where there is a problem in side electromagnetic radiation. Master’s thesis made and designed in the form of an explanatory note, which includes 100 pages and presentation that includes 5 figures

    Keywords: the leak, electromagnetic radiation surge protector

    The work consists of:  86 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Methods of processing signals in nonlinear radar review

    Author: Hatashov Olexandr

    Group: РВ31м

    Supervisor: Professor Zinkovskyi Yuri

    ELK: Master

    Speciality: 8.05090201 Radioelectronic Devices and Facilities

    Summary: Volume master’s thesis is 106 pages, which includes 33 illustrations, 6 tables, 28 bibliographic titles for references. Relevant issues considered secondary signal processing response of nonlinear radar. The purpose of the study was floated on the probing signal spectrum of the signal response of a nonlinear lens radilokatsiyi. The existing design nonlinear radilokatoriv, a table with comparisons of their characteristics. The analysis of the secondary field of nonlinear radar, it was shown how its characteristics vary depending on the type of irradiated nonlinearity.

    Keywords: nonlinear radar, secondary signal response microstrip line rozsivachi nonlinear, parametric fertilizer

    The work consists of:  108 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    A device for transmitting telemetry data to the remote object

    Author: Buriachynskyi Maksym

    Group: РВ-31м

    Supervisor: Levandovskyi Vitalii

    ELK: Bachelor

    Speciality: 8.05090201 Radioelectronic Devices

    Summary: Magister’s dissertation is devoted to developing devices for the transmission of telemetry data from the remote object on the computer. A device for transmitting telemetry data can be used in various industries, the remote observation of the process in difficult access areas where cable is not economically profitable, or when you want maximum speed the deployment of telemetric network (eg, emergencies). The use of wireless data transmission provides a fast, reliable and high-quality connection between the sensors and processing center, and provide to respond to unpredictable situations in real time. However, the autonomy system and the compact dimensions allow you to quickly install the device on moving objects, and in remote areas, making the device indispensable to many industries, as well as emergency situations. Diploma thesis is designed as an explanatory note containing 69 sheets, and graphic part – 3 sheets of A4.

    Keywords: radio modem, cd, wireless transmission

    The work consists of:  64 pages of explanatory note and 3 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Digital radio beacon

    Author: Lutsenko Mykyta

    Group: РІ-11

    Supervisor: Diuzhaev Leonid

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: Thesis presented 53 pages containing 13 illustrations, 1 table, 4 applications. The purpose of this project is to create software for the device that will work as a starting point for determining the specific location where it will be installed. Specifically, the device transmits digital broadcasting code in a limited distance. The code will contain information on the place in which it is located. These beacons can be installed on city transport stops and will send that data to information to stop (digital code which will then be passed directly to the receiver in a given vehicle that will allow them to fix with 100

    The work consists of  63 pages of explanatory note, 1 appendix and 3 drawings

    Explanatory note: Full text

    Posters:

  • Схема електрична принципова
  • Мікроконтролери AVR
  • Алгоритм Роботи Програми
  • Laser laboratory stand for research of biological objects

    Author: Panfilov Nikita

    Group: РБ-11

    Supervisor: Golovnia Viktoria

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: The research paper developed by the laboratory stand for research of biological objects. Thesis is devoted to the topical issue of rapid analysis of large arrays with pathological deviations from the norm in a wide spread of ultrahazardous viral and infectious diseases. The paper analyzed the existing methods and devices that implement the determination of the parameters of biological objects to interact with them using laser radiation. Constructive and optical calculations and design developed by the laboratory stand. The work consists of four sections, a list of references and applications. The first section of the study carried out inspection of facilities that are used for diagnosis. The second section is devoted to the analysis of existing methods of laser diagnostics, shows the interaction of laser radiation with biological objects. The third section is designed experimental stand for laboratory studies of blood. The last section deals with the protection of labor. Work carried out on 68 pages, 17 illustrations are presented and 8 tables.

    Keywords: speckle interferometry, laser speckle pattern diagnosis.

    The work consists of:  71 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Detector of eavesdropping devices disguised into the rea elements

    Author: Fedorchuk Taras

    Group: РІ – 11

    Supervisor: Yevgrafov Dmytro

    ELK: Bachelor

    Speciality: 6.090502 Radioelectronic Devices

    Summary: Detector of eavesdropping devices disguised into the REA elements. In this diploma project develops detector embedded devices with AVR microcontroller. Diploma project Fedorchuk T.V. “KPI”, Department of Radio Engineering, Department of designing and manufacturing electronic equipment, a group of PI-11. KPI, 2015. – Pages – 74, figures – 28 tables – 10 drawings – 3. This project is designed detector embedded devices with AVR microcontroller. The main purpose of this device is recognition eavesdropping devices or individual elements CEA, such as: resistors, capacitors, Diodes, Inductance. The device can be connected to your computer via USB. The project includes a graphical documentation, which includes: structural design of the electrical drawings, electrical principle drawing schemes, the draft contains the results of measuring device

    Keywords: detector, eavesdropping devices, microcontroller, measurement

    The work consists of  78 pages of explanatory note, 3 appendix and 3 drawings

    Explanatory note: Full text

    Drawings:

  • Еквівалентні схеми
  • Схема електрична принципова
  • Покази дисплею
  • Electronic base of qualifying diploma works

    Author: Zhurakhovskyy Dmytro

    Group: РІ-11

    Supervisor: Adamenko Yuliia

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: Qualifying work on the topic “Electronic Base Of Qualifying Diploma Works” is performed on the 74 pages, which includes 29 illustrations, 3 tables, 3 appendixes and 1 bibliographic references. The aim of this work is to develop an electronic base of qualifying diploma works integrated with the site of Department of Design and Production of Radioelectronic Equipment for promulgation, public awareness with the content of qualifying works and prevention of an academic plagiarism. To achieve set purpose, peculiarities of database forming was analyzed in this paper, comparative characteristics of content controlling systems was performed, full conception of resources (including content, decoration, arrangement and theming) was designed, the selection of modules for providing set resource purposes was explained and electronic database in the shape of site was built.

    Keywords: electronic database, qualifying diploma work, ntuu «kpi», department of design and production of radio electronic equipment, «antiplagiarism»-software, drupal.

    The work consists of  74 pages of explanatory note, 1 appendix and 3 drawings

    Explanatory note: Full text

    Posters:

  • Задачі інформаційного ресурсу «Електронна база атестаційних робіт»
  • Структура бази атестаційних робіт
  • Концепція інформаційного ресурсу
  • Emergency lighting device

    Author: Khalaim Vasil

    Group: РІ-11

    Supervisor: Marianna Vodolazka

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: The aim of the degree project was designing emergency lighting. Developed schematic diagram of a qualitatively new functionality and calculated structural parameters of the device. Explanatory note consists of an introduction, eight chapters, conclusions, list of sources and applications that include the terms of reference, the specifications and a list of items to the drawings. Explanatory note containing 6-tables 25 faces and figures. Graphic material consists of a block diagram (A3) concept (A1), assembly drawings (A3) and the PCB (A2) of control unit, assembly drawings (A2) and the PCB (A2) of LED lamp. The results of this study can be used to improve existing emergency lighting or manufacturing application of the new device with the additional refinement of design and functionality.

    Keywords: emergency light, printed circuit board, led lamp, power management, microcontroller, sensor lighting, rechargeable power supply

    The work consists of  58 pages of explanatory note, 5 appendix and 6 drawings

    Explanatory note: Full text

    Drawings:

    Development of the complex thermal cooling of highly sensitive amplifier systems for radiometric measurement of weak signals

    Author: Shulga Vitalii

    Group: РБ-11

    Supervisor: Yanenko Alexey

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: The diploma project was conducted to study the development of the complex thermal cooling of highly sensitive amplifier systems for radiometric measurement of weak signals; developed electronic circuit model design is developed with support of their design decisions. The given calculations confirming operability of the device and accuracy of carrying out measurements. The instruction on use of the model is developed. As a result of this work is made with a set of layout design documentation, which is confirmed by the introduction. The diploma project contains 47 pages explanatory note 13 illustrations, 7tables 4 drawings 2 application 12 bibliographical references.

    Keywords: thermoelectric coolers, cooling, amplifier, amplification factor, design, complex, dd.

    The work consists of  47 pages of explanatory note, 2 appendix and 5 drawings

    Explanatory note: Full text

    Drawings:

  • Блок охолодження, складальний кресленик
  • Гвинт
  • Радіатор
  • Термостат
  • Структурна, плакат
  • Low-frequency amplifier

    Author: Nilskyi Bogdan Oleksandrovych

    Group: РВ-11

    Supervisor: Senior Lecturer Popsuy Vladimir

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: In this thesis project was implemented low frequency amplifier; made revision and modification of the electrical principle schemes amplifier, making circuit boards. The calculations for the design of the printed circuit board and the calculation of the vibration. In the end the project was obtained with minimal material costs workable device.

    Keywords: amplifier, board, elements, frequency, pcb, ere.

    The work consists of  49 pages of explanatory note, 7 appendix and 5 drawings

    Explanatory note: Full text

    Drawings:

    Weather weather station based microcontroller

    Author: Matiiuk Maksim

    Group: РВ-11

    Supervisor: Diuzhaev Lionid

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: The purpose of this diploma project is to develop a home-based meteorological weather microcontroller. The project developed the scheme using microcontroller ATMEGA32-16PU, based schemes conducted choose components. A printing unit and conducted design choices. Carried out the necessary calculations to confirm the efficiency of the device and compliance standards and regulatory documents. This device can be used in homes to control temperature and humidity, and to monitor atmospheric pressure.

    Keywords: weather weather station, atmega32, design documentation

    The work consists of  60 pages of explanatory note, 3 appendix and 3 drawings

    Explanatory note: Full text

    Drawings:

    Computer simulation of bioobject’s speckle interference patter

    Author: Chmykh Anton

    Group: РБ-11

    Supervisor: Mykola F. Bohomolov

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: In process of work, analysis algorithm of patterns of speckle-interference was developed and program for аnalysis of correlation dependences of speckle pattern for the normal and pathological conditions objects.in MatLab 2014a environment. Work consist of introduction, 4 chapters, conclusion, the list of used literature and sources, 1 attachments, which include listing. It also include 1 table, 40 figures. The results of this work can be used for further development of software for the rapid analysis of biological objects.

    Keywords: speckle interferometry, blood, laser radiation cross-correlation.

    The work consists of:  91 pages of explanatory note and 2 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Measuring light transmittance glass

    Author: Kruhal Anton

    Group: РВ-21

    Supervisor: Zinchenko Maksim

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: The degree project consists of explanatory note volume 71 pages (16 illustrations, 12 tables and 24 links) and 4 drawings. The project is dedicated to the development taumeter – device measuring optical transmission glass. Analyzed the current regulatory requirements for the reporting unit. The analysis counterparts, resulting in the election was the most successful prototype and technical solutions. The emphasis in the design is on minimizing electrical circuit elements fundamental to the conservation tehnikometrolohichnyh Development features that significantly reduce energy consumption and the cost of the product. Submitted comply with the relevant regulations and standards concerning the measurement of light transmission glass. The primary concerns of the introduction device traffic police stations vehicle maintenance and more.

    Keywords: taumetr, light transmission glass, processing digital signal

    The work consists of  90 pages of explanatory note, 3 appendix and 4 drawings

    Explanatory note: Full text

    Drawings:

  • Схема електрична принципова
  • Друкована плата
  • Друкований вузол
  • Корпус
  • Generator based on direct digital synthesis

    Author: Karlik Roman

    Group: РВ-11

    Supervisor: Novosad Andriy

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: The aim of this graduation project is development of the generator based on direct digital synthesis. The project represents the generator’s scheme based on the integral DDS scheme; based on the scheme, the choice of the element basis was conducted. Also, the project contains the PCA (Principal component analysis) and the choice of construction option. All necessary calculations were conducted in order to confirm the efficiency of the device and accordance with all standards and statuary documents. Facts about the extent of explanatory note: Given generator can be applied in various laboratories of scientific research or service centers as the source of stable analog waves.

    Keywords: generator, microcontroller, digital synthesis, analog waves.

    The work consists of  68 pages of explanatory note, 2 appendix and 4 drawings

    Explanatory note: Full text

    Drawings:

  • Генератор.Схема електрична структурна.
  • Генератор.Схема електрична принципова.
  • Плата
  • Друкований вузол
  • The probing sonar device

    Author: Kirienko Serhii

    Group: РВ-11

    Supervisor: Koval A.

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: The objective of this thesis project was to develop design block formation of the probe pulse sonar. In its design must take into account several factors. The device must meet therequirements of the customer, be economical in terms of power, have a minimum sizeand weight, be easy to use and be available at a price. However, this device should be in production technology and reliable to use. While the work was designed PCB, selectedadvanced components and is designed safety device. As a result, received a set of documents suitable for implementation into the productionunit In the " Оccupational safety and health " was the analysis of safety of this product.

    Keywords: sounder, sounding device, transformer calculations

    The work consists of  121 pages of explanatory note, 12 appendix and 6 drawings

    Explanatory note: Full text

    Drawings:

    Thermostat

    Author: Pukhter Vadym

    Group: РБ-11

    Supervisor: Golovnia Viktoriia

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: The purpose of experimental design is to develop a device widely available to control room temperature, which will rationalize energy consumption in the winter. In the course of implementation of the task considered existing analogues of thermostats in Ukraine and analyzes these prototypes past years. During the review of previously proposed circuit solutions symistornyh regulators deeply processed all the important stages of development, production prototype, practical tests on the performance and functionality of simple transformations on circuit level. Also monitored process improvement and improve functional properties of the device based on the evolution of the components of electronic equipment. Features such improvements in the project used to improve ergonomics and versatility of the device and fixed by the corresponding calculations. In the process are using computer-aided design in accordance with recommendations of the relevant training course. There is results of the working in programs P-CAD, MathCad, AutoCad, MS Excel. The total amount of work is 73 pages, number of illustrations — 34, tables — 4, bibliographic items — 16.

    Keywords: the thermostat, control semistorny

    The work consists of  73 pages of explanatory note, 9 appendix and 4 drawings

    Explanatory note: Full text

    Drawings:

    Diagnosis of diseases of the human eye imaging methods

    Author: Starynenko Olga Andriivna

    Group: РБ-11

    Supervisor: as. Golovnia V.M.

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: In the thesis work optimized operation of the appliance spectral coherence tomography. The work consists of five chapters. In the first chapter the analysis of noninvasive optical and laser methods of diagnostics of diseases of the human eye. In the second and third sections reviewed and analyzed the principles of spectral instruments and mathematical signal processing respectively. In the fourth chapter proposed alternative broadband optical radiation source and given their characteristics. In the fifth chapter the problems of safety and security when using the device. References consists of 14 sources.

    Keywords: optical coherence tomography

    The work consists of:  94 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Device for control servoprivod

    Author: Rudov Oleg Myhaylovich

    Group: РІ-11

    Supervisor: Novosad Andriy Anatiliyovich

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: Im gegebenen Diplomprojekt war der Block der Fernsteuerung vom Servoantrieb nach dem Radiokanal entwickelt. Im Projekt ist die ausführliche Beschreibung des Schemas vorgestellt, einige berechnete kaum-Bullen Schemen und ist die Berechnung der Weite der Verbindung durchgeführt, sind Konstrukzion entwickelt. War die Elementbasis mit den Charakteristiken jedes Elementes gewählt. Im Verlauf der Entwicklung war die Berechnung der Umfänge der Druckzahlung, der Elemente der Druckmontage, der Trassierung der Zahlung, die Berechnung der Vibrationsfestigkeit der Konstruktion durchgeführt. Es war die Zuverlässigkeit der Konstruktion, die Berechnung der Trägheitskraft und der biegenden Momente, der Anstrengungen auch berechnet. Ausgehend von den Ergebnissen der Berechnung, war der Körper der Konstruktion gewählt.

    Keywords: beschreibung des schemas vorgestellt

    The work consists of  50 pages of explanatory note, 2 appendix and 4 drawings

    Explanatory note: Full text

    Drawings:

  • Структурна схема
  • Схема електрична принципова
  • Друкована плата
  • Плата
  • Develop a control module electro boiler

    Author: Kazban Mykola

    Group: РІ-11

    Supervisor: Tarabarov Sergey

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: The purpose of this diploma project is to develop a control module electro boiler. The project developed a schematic diagram of the module using registers and indicators based on the schemes conducted choose components. And structural materials. Developed printing unit and conducted design choices . Carried out the necessary calculations to confirm the efficiency of the device and compliance standards and regulatory documents. Information on the amount of explanatory note: Number of explanatory note 57; Number of illustrations 12; Number of Table 7; Number of drawings 3; Number of links 9. This module can be used for electro boiler control units to adjust and display the temperature of water in the heating system.

    Keywords: вoiler, module, component, reliability, printed node vibration, indicators.

    The work consists of  55 pages of explanatory note, 1 appendix and 3 drawings

    Explanatory note: Full text

    Drawings:

  • Модуль управління та індикації електроопалювальних котлом. Схема електрична принципова
  • Друкована плата
  • Вузол друкований. Складальний кресленник
  • Matrix led display

    Author: Deineka Oleksandr

    Group: РВ-11

    Supervisor: Pohrebniak V.

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: The degree project consists of explanatory note volume 70 pages, includes 18 figures, 21 tables, 7 drawings, 13 references, 2 applications. The aim of the degree project is to develop a management fee matrix LED display. The project analyzes the requirements for modern traveling lines. Studied counterparts, the optimum base element and select the most effective technical solutions. Based on research data designed printed circuit board, selected necessary parts. The calculations, which confirm efficiency of the device and compliance with all regulations and standards. Developed device recommended in enclosed premises and premises under a canopy.

    Keywords: diode matrix display, microcontroller, pcb control unit

    The work consists of  80 pages of explanatory note, 3 appendix and 6 drawings

    Explanatory note: Full text

    Drawings:

  • Схема електрична принципова 1
  • Схема електрична принципова 2
  • Друкована плата 1
  • Друкована плата 2
  • Друкований вузол 1
  • Друкований вузол 2
  • Means of improving and ensuring the quality of sound and image in digital tv systems

    Author: Hadzhylov Yaroslav Valerievich

    Group: РІ-31м

    Supervisor: Demyanenko Petro Opanasovych

    ELK: Master

    Speciality: 8.05090203 Intelligent Technologies of Microsystems Radio Electronic Engineering

    Summary: A research object is a methods of transmission of picture and sound signals in systems of digital TV broadcasting. Research was carried out by using of materials, which were written by native and foreign scientists for a few last years. Systematized the impact of individual processes the signal image and sound quality of reproduction in the subscriber terminal. Try playing as a comparative depending on the parameters of image compression applied during the transmission of digital television signals, obtained experimental dependences that establish the link between subjective and objective methods of evaluating image quality of digital television. The results can be used in the educational process of training and retraining in the field of television broadcasting and transmission of digital multimedia content by means of telecommunications networks. Results can also be used during the planning and building and operation of digital television broadcasting networks.

    Keywords: video sequence, pixel, frame, video codecs, redundancy, video compression, image quality, distortion, codec, correlation

    The work consists of:  110 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Grain drying device with bilateral irradiation

    Author: Vaskovets Vadym

    Group: РБ-11

    Supervisor: Yuri K. Sydoruk

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: This work is presented in 86 pages, which contain 38 figures, 4 tables, 18 sources and 1 appendix. The aim of the thesis is the theoretical data inference for a dryer. The principle of the machine is based on the use of microwave electromagnetic field. We consider the optimal variant of the SHF dryer using low-to medium-power magnetrons (SHF energy generator), as well as individual units that make up the device. The subject is to calculate the distribution of electromagnetic field on the basis of absorption and phase of the reflected wave at bilateral irradiation by SHF electromagnetic field.

    Keywords: electromagnetic field, generator, grain, magnetron, shf drying, radiation, optimization, absorption, distribution, drying.

    The work consists of:  86 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Laboratory studies of the biophysical characteristics of blood formennyh

    Author: Dubovik Victor

    Group: РБ-11

    Supervisor: Mykola F. Bohomolov

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: This thesis is devoted to the topical issue of laser diagnostics, namely to the speckle interferometry. The aim of this paper is the necessity for preliminary statistical analysis during the comprehensive diagnostic studies of blood formed elements characteristics under normal and pathological conditions. The work itself consists of four chapters, a list of references and appendix. In the first chapter the functions of blood, its formed elements, their size and functions are described. The second chapter provides the general characteristics of lasers and their application in medicine. The third chapter highlights the biophysical characteristics of blood cells and their processing in Matlab. The fourth chapter deals with the problems of professional safety when using the device. The volume of work is 76 pages including 17 illustrations, 8 tables, an appendix and 15 references.

    Keywords: speckle interferometry, environment matlab, biophysical characteristics, red blood cells, white blood cells, blood.

    The work consists of:  76 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Research based on nonlinear lens plane spiral antenna

    Author: Galitskiy Alexander Pavlovich

    Group: РВ-31м

    Supervisor: Zinchenko Maxim Vyacheslavovich

    ELK: Master

    Speciality: 8.05090201 Radioelectronic Devices and Facilities

    Summary: Volume explanatory note is 129 pages, which includes 55 illustrations, 8 tables, 3 annexes and 52 bibliographical name on the list of references. Considered relevant issues of telecommunication systems, rational use of spiral antennas resolved many practical tasks for-that will determine the quality and quantity of radio systems is developed. The purpose of the study of nonlinear lens on the basis of flat spiral antennas: modeling and analysis of the characteristics, advantages and disadvantages definition devices. The analysis of characteristics, radiation spiral flax antenna, calculating the components of the electromagnetic field simulation broadband lens among MMana, MathCad received: The diagram of the nonlinear fertilizer; Energy characteristics of components in the signal response is nonlinear scattering th; Got the possibility of using nonlinear lens as physical models of embedded devices.

    Keywords: chart orientation, nonlinear radar, nonlinear lens, the signal response spiral antenna radiation

    The work consists of:  129 pages of explanatory note and 3 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Block stabilization pre amplifier

    Author: Batrak Evhen

    Group: РВ-11

    Supervisor: Pohrebniak V.

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: Development of block stabilizers preamplifier power was conducted in this diploma project. The electronic circuit of devices was developed in work, development of construction of device is conducted with motivation expedience of the accepted decisions of designers. A reliability security, capacity and technologicalness of block stabilizers analysis is resulted. A work performance is a set of designer document, necessary for making of device in practice. In a section « Labour safety » was conducted estimation of the most harmful and dangerous factors at development and making of block stabilizers.

    Keywords: the stabilizer, power amplifier, cad

    The work consists of  47 pages of explanatory note, 3 appendix and 5 drawings

    Explanatory note: Full text

    Drawings:

    Nonlinear lens detection method for the secondary radiation

    Author: Balitskyi Vitalii

    Group: РВ-31м

    Supervisor: Zinkovskyi Yuri Frantsovych

    ELK: Master

    Speciality: 8.05090201 Radioelectronic Devices and Facilities

    Summary: The work is to identify the tell-tale signs of secondary semiconductor LDCs in order to increase efficiency of nonlinear radar to search for eavesdropping devices in the field of technical protection of information. The study involved secondary analysis of tell-tale signs of internal effects in semiconductor structures LDCs during the relatively strong nonlinear probing signal radar. The aim of the thesis is to study the response of a nonlinear lens structure to ensuring the effective identification of the latter. Implementation of the operation in practice of technical protection of information has practical and scientific value and increases the efficiency of the installation, identification and localization of eavesdropping devices means nonlinear radar. Based on materials dissertation published 1 scientific work on “Over-securing remote detection of objects in nonlinear radar”. Master’s thesis consists of an introduction, three chapters, conclusion and bibliography. The work contains 120 pages, 27 figures and 7 tables. References includes 45 titles.

    Keywords: nonlinear radar, nonlinear lens, the signal response, secondary radiation protection information zakladniy device, tell-tale sign of noise.

    The work consists of:  130 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Experimental stand for researching of bulk dielectric materials drying with electromagnetic microwave field

    Author: Yablunivskiy Anton

    Group: РІ-11

    Supervisor: Turovskyy Anatoliy

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: Diploma project consists of 49 pages and contains 16 figures, 2 tables, 24 reference and 3 appendixes. The aim of the project is developing of experimental stand for researching of bulk dielectric materials drying with electromagnetic microwave field and optimization of the main parameters of the processing chamber. The calculation and optimization of the parameters such as thickness of the processing chamber, in which grain material irradiation occur, and distance between the processing chamber and adjacent polarizing reflector, which will ensure the maximum value of uniformity of the field distribution. The design documentation, including drawings on the radiator assembly and individual parts: waveguide, slotted plate and mounting plate, electrical circuit for magnetrons supplying unit, is developed.

    Keywords: dielectric bulk materials, electromagnetic wave, grain, irradiation, polarizing reflector, processing chamber, waveguide, microwave

    The work consists of  49 pages of explanatory note, 3 appendix and 5 drawings

    Explanatory note: Full text

    Drawings:

  • Випромінювач. Складальне креслення
  • Плита
  • Хвилевід
  • Кріплення
  • Плата живлення. Схема електрична принципова
  • Power amplifier of ultrasound oscillations

    Author: Boiko Oleksandr

    Group: РВ-11

    Supervisor: Novosad Andriy

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: The purpose of the bachelor’s thesis is to develop a design for signal power amplification in order to drive the piezoelectric ultrasonic emitters. Analysis and digital simulation of the amplifier circuit diagram are carried out in the framework of the graduation project . The selection of the circuit element base is made in accordance with the diagram. The thesis presents the transformer for matching the output impedance of the amplifier and the resistance of the piezoelectric transducer, which is a load of the amplifier. Printed circuit board assembly is elaborated as well as the selection of the construction is made. The necessary calculations to confirm the device working capacity in compliance with standards and regulatory documents are performed. Potentially dangerous and harmful factors, which may occur in the design process, are identified in the course of devixe operation

    Keywords: amplifier, emitter, transformer, ultrasonic oscillations, analog signal.

    The work consists of  70 pages of explanatory note, 3 appendix and 4 drawings

    Explanatory note: Full text

    Drawings:

  • Підсилювач потужності ультразвукових коливань. Схема електрично принципова
  • Плата
  • Вузол друкований. Складальний кресленик
  • Плакат результатів моделювання
  • The daily fetal monitoring of electrocardiogram during pregnancy

    Author: Zinger Yana Leonidovna

    Group: РІ-31м

    Supervisor: Nelin Yevgeniy Andrijovych

    ELK: Master

    Speciality: 8.05090203 Intelligent Technologies of Microsystems Radio Electronic Engineering

    Summary: In this work examined the physiological parameters of fetal electrocardiogram and mother. The methods of diagnosis of the fetal heart and the existing definition of the parameters of the electrocardiogram. Propose a method of daily fetal monitoring that allows registration of the electrocardiogram of the fetus during the day, and the algorithm to extract fetal electrocardiogram signals from a mixture taken with abdominal findings. Investigated the method of blind source separation for extraction of the fetal electrocardiogram. The study simulated electrocardiogram signals the mother and fetus, which had suffered random noise, for further processing. A result of testing and calculation of error proved that the method of blind source separation gives better accuracy than adaptive.

    Keywords: fetal monitoring, electrocardiogram, abdominal, blind source separation

    The work consists of:  93 pages of explanatory note and 2 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    The system concentration of electromagnetic fields from microwave n sources in one volume

    Author: Slobodenyuk Andrii

    Group: РВ-31м

    Supervisor: Sydoruk Yurii

    ELK: Master

    Speciality: 8.05090201 Radioelectronic Devices and Facilities

    Summary: Volume explanatory note is 142 pages, which includes 59 illustrations, 4 tables, 1 addition and 51 names on the list of bibliographic references. Examined topical questions of development and designing of system concentration of electromagnetic fields microwave for drying bulk materials. Purpose of the work consisted in design and research of concentration of electromagnetic microwave field. Existing devices for drying bulk materials, lighting their main weaknesses. Researched possible construction of concentration of electromagnetic fields. As a result of theoretical analysis polarizing filters, tanning theoretical analysis of structures, calculation of field distribution, calculation of field in the area of energy concentration electric field of microwave range developed a simplified system concentration of energy from reflector.

    Keywords: extremely high frequency, dryers, bulk materials, microwave device, waveguide antenna, reflector antennas.

    The work consists of:  142 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Radiation device electromagnetic field of liquid and semi-fluid environments

    Author: Nakonechnyi Taras

    Group: РВ-11

    Supervisor: Sydoruk Yurii

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: In the thesis the device of radiation of liquid, semi-fluid environments by means of an electromagnetic field is developed. Work contains 15 illustrations, 4 tables. The purpose is creation of the device which will be able to disinfect liquid and semi-fluid environments by means of the microwave oven of radiation. Created the device to consume energy several times less than a thermal way of disinfecting and is more suitable for further use on lime application. In work two options of the device are investigated: the first option for radiation of the liquid environment second for radiation of the dense environment. In both devices Wednesday, it is disinfected moves continuously devices can be given to the device continuously material for disinfecting and to use as the industrial equipment for disinfecting of the environment. The offered equipment can be used for disinfecting of mules, household drains and other similar cases

    Keywords: disinfection, microwave irradiation, mule

    The work consists of  85 pages of explanatory note, 1 appendix and 7 drawings

    Explanatory note: Full text

    Posters:

    Measuring blood sugar by kulonometrychnym

    Author: Balahtar Ganna S.

    Group: РБ-11

    Supervisor: Golovnya Victoria Milentivna

    ELK: Bachelor

    Speciality: 6.050902Radioelectronic Devices

    Summary: Causes of disease diagnosis which is kulonometrychnym method, the impact of these diseases on human performance. Analyzed the principles of the method and kulonometrychnoho ampermetrychnoho method, and their use in devices. A structural unit of the device for a specified level of blood sugar kulonometrychnym method. The work described in 85 pages containing 20 tables and 9 figures and 2 of annex 18 names on the list of bibliographical references.

    Keywords:

    The work consists of:  85 pages of explanatory note and 1 appendix

    Explanatory note: Full text

    Posters:

    Презентація

    Synthesis microstrip bandpass filter based on electromagnetic crystals

    Author: Ivanitskii Anton

    Group: РВ-11

    Supervisor: Adamenko Yuliia

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: Thesis entitled "Synthesis microstrip bandpass filter based on electromagnetic crystals " made on 52 pages including 27 illustrations, 2 tables , 1 appendix and 22 citation The aim of this work is to develop synthesis algorithm microstrip bandpass filter based on electromagnetic crystal. To address this goal characteristics of electromagnetiс crystals and its irregularities were analyzed . Aspects of construction of filters with different characteristics based on electromagnetic crystals were reviewed. The features impedance EC approach to the design , including the definition and calculation of parameters irregularities EC. The adaptation of methods of synthesis of microwave structures at EC , taking into account EC- irregularities. The synthesis of EC was made to create a band-pass filter for a given frequency characteristics . Results of synthesis were compared with existing frequency – selective device based on EC

    Keywords: electromagnetic crystal (ec), ec- irregularities, egb, dgs, synthesis, amplitude frequency response, bandpass filter

    The work consists of  61 pages of explanatory note, 1 appendix and 4 drawings

    Explanatory note: Full text

    Posters:

    Device control parameters mechatronic system

    Author: Gunko Igor

    Group: РВ-11

    Supervisor: Novosad Andriy

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: Diploma project consists of 60 pages containing 17 illustration withs14 tables, 4 applications and 12 references. The aim is to develop a device control parameters mechatronic system that is designed to measure the pressure in the system and send the results to a personal computer. The calculations confirm efficiency of the device and compliance with all regulations and standards. The developed device control is recommended in laboratories or at home.

    Keywords: device control, pressure control mechatronic system, block diagram of a mechatronic module

    The work consists of  71 pages of explanatory note, 4 appendix and 4 drawings

    Explanatory note: Full text

    Drawings:

    Microcontroller-based trip computer

    Author: Artemenko Dmytro Serhiyovych

    Group: РВ-11

    Supervisor: Pogrebnyak Vitaliy Petrovych

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: The degree project consists of an explanatory note on 93 pages, includes 20 illustrations, 20 tables, 5 drawings, 16 links, 2 appendices. The purpose of the degree project is the operating payment development of the graphic display for reflecting the current state of knots and units of the vehicle. The project analyzed the requirements for modern on-board computers. Analogs are investigated, optimum element base is picked up and the most effective technical solutions are chosen. It is designed the printed circuit board of the on-board computer based on research data, the required components are chosen. The calculations confirming operability of the device and compliance to all normative documents and standards are carried out. The developed on-board computer is recommended to be used on vehicles of a middle and budgetary class.

    Keywords: on-board computer, microcontroller, printed circuit board, control unit.

    The work consists of  93 pages of explanatory note, 2 appendix and 5 drawings

    Explanatory note: Full text

    Drawings:

    The model for the study of the characteristics of oscillographic galvanometers

    Author: Klekotyuk Vitalii

    Group: РВ-11

    Supervisor: Popsuy Vladymyr

    ELK: Bachelor

    Speciality: 6.050902 Radioelectronic Devices

    Summary: The diploma project was conducted to study the development of the model characteristics of the oscillograph galvanometer; developed electronic circuit model design is developed with support of their design decisions. The given calculations confirming operability of the device and accuracy of carrying out measurements. The instruction on use of the model is developed. As a result of this work is made with a set of layout design documentation, which is confirmed by the introduction.

    Keywords: oscillographic galvanometer, design, model, DD.

    The work consists of  50 pages of explanatory note, 3 appendix and 6 drawings

    Explanatory note: Full text

    Drawings: